Showing results: 31 - 39 of 39 items found.
-
HMa -
Lectrosonics, Inc.
This unique plug-on transmitter design will ideally match any microphone or line level source via a standard XLR connector. Phantom power is selectable at 5, 15 and 48 volts, or can be turned off for use with dynamic microphones and line level signal sources.
-
Machine Vision -
Vision Research Inc.
Capture the power of Phantom High Speed imaging in machine vision streaming applications. Image data flows directly to a frame grabber and PC or long record DVR via CXP protocol. Data is immediately accessible and limited only by the amount of storage in the PC or DVR.
-
Alfamation S.p.A
Infotainment systems have to deal with a several RF signals, starting from world radio standards but extending to mobile communication, GPS & WLAN. Most of the H.U. RF connections provide phantom power to active antennas that should be tested at different loading conditions (on more values, yet different case by case).
-
Supreme Instrument Laboratories
Supreme make Phantom Load Test Set is a portable testing accessory designed for field service. It simulates various load conditions usually prevailing in power supply system. The unit offers a practical solution by providing artificial load unaltered by the variation in the power supply mains and adjustable to the complete meter testing requirements.
-
PRE-01 -
Audiomatica
The microphone preamplifier PRE-01 has been designed to match Audiomatica’s microphones MIC-01, MIC-02 andMIC-03. It is particularly useful when the microphone has to be operated far from the analyzer or when weighted measurements are needed. PRE-01 powers the microphone connected to its input with an 8.2V phantom supplyand adds a selectable weighting filter (A or B or C); also available there is a 20 dB gain stage
-
CT100 -
BEHRINGER International GmbH
The intelligent, CPU-controlled CT100 accepts virtually any connector type: XLR, mono and TRS phone ( 1 /4 ", 1 /8 ", TT), RCA and MIDI. It shows which input pin is connected to which output pin. Separate LED's indicate proper shield connection and phantom power presence. The CT100 also offers an installed cable test mode and a continuity check plus a test tone generator.
-
XLR Sniffer/Sender -
Sound Tools
Designed by Rat Sound to deal with the "real world" of pro audio, the SoundTools Sniffer/Senders are the perfect tools for live environments. Test snake lines and cables when the ends are at a distance and avoid running extra cables just to test. Utilizing phantom power the Sniffer end can quickly test snake lines in minutes. The aluminum barrels eliminates the problem many testers face with solder joints failures and the unit will never rust. 3 simple LED’s will instantly diagnosis your cable as it tests for every possible shot, open, or cross wire in XLR cables. If the LED’s read all green you cable will work!
-
3 Series -
Powermetrix Systems
Powermetrix continues its industry leadership with the introduction of Powermetrix Remote Manager (PRM) for the PowerMaster® 3 Series. Powermetrix Remote Manager enables wireless control of essential and various metering site accuracy tests contained within PowerMaster® 3 Series from any Windows compliant system up to 100 feet in any environment, including high EMF environments! Customer load Meter Testing, CT/PT ratio testing, CT/PT burden measurement, meter register/demand testing, and wiring verification are all easily performed with this extremely portable, hand-held 3-phase power analyzer. In addition, with the new Model 335, phantom load meter testing and CT burden added testing are available to complete your field-testing needs.
-
CLIOQC Model V -
Audiomatica
The QCBOX Model 5 is a non-conventional unit designed to fulfil actual and future needs of an electro-acoustical analyzer like the CLIO system. It is USB linked to a PC and can be configured, with dedicated software controls, to assist frequency response and impedance measurements or to perform DC measurements. Using it for frequency response measurements acts as 50W power amplifier to drive the speaker or network under test while routing one-of-four inputs to the analyzer as well the current sensing output. The four inputs are able to provide a phantom power supply both for Audiomatica or general purpose microphones (0-24 V range, software controlled). Impedance measurements can be done either switching the D.U.T.’s load across the analyzer’s input or using a dedicated output, ISENSE, thus allowing impedance measurements in constant voltage mode as well voice coil current distortion analysis. An internal ADC measures the DC current into the voice coil. Thanks to an internal software controlled voltage generator the speaker can be driven with a superimposed DC voltage (±20V), allowing for measurements of large signal parameters. Two ADC converters with a ±2.5 V and ±5 V are available at inputs 3 and 4 to measure the displacement with a laser sensor or any other DC signal. A dedicated digital input handles an external foot pedal switch (or TTL signal) to be connected and triggers QC operations. A 6 bit output – 5 bit input TTL digital port is available to interface the QCBOX and driving software with external hardware (like turntables for example).The QCBOX Model 5 finds use both in laboratory for R&D applications and in production lines setups.
